Balar Put the cable into the connector. The plotter will work normally, but it will not be able to use any PML functionality. Overlay — Front panel overlay Self adhesive — Shows the function of the front panel buttons and indicator lights Italian. The cartridges are shutdown: The meaning of the error codes is explained on page A dual lens system with a unity conjugate ratio system directs the light from the illuminated surface to the line-sensor. Overlay — Front panel overlay Self cm — Shows the function of the front panel buttons and indicator lights German.
|Published (Last):||8 December 2012|
|PDF File Size:||4.61 Mb|
|ePub File Size:||17.95 Mb|
|Price:||Free* [*Free Regsitration Required]|
C Functional Overview Media-Axis Mechanism The media X-axis motor is mounted under the right endcover and is electrically connected to the main PCA, which contains the media-motor driver.
Turn Queing to OFF in the front-panel. Carriage sensor does not correctly find media edge. Switch the plotter OFF. In order to access the trailing cable behind the electronics enclosure, perform the following steps: Label — Safety label — Provides warning that encoder strip is sharp.
Drop Detector seevice Lift end-tabs to release cables. Demonstration Plot You can check proper plotter operation by plotting and examining the demonstration esrvice, which is resident in the plotters. Third-party ink and off- axis ink systems.
Tx15 10 Manal the media motor towards the rear of the plotter. Voltage Vac 1. Loopback connector HP Part Number The Y-axis maintenance kit includes a cloth and alcohol dssignjet clean the slider rods properly, and a lubricant to apply onto the rods.
Serious shock hazard leading to death or injury may result if the plotter is not properly grounded. The accuracy calibration includes calibration of the optical sensor on the carriage. Press the Enter button to clear the message from the front panel display. PostScript is also available when the Postscript upgrade is fitted. This band is normally located between 65 and 75 mm from the top border of the paper. As a result, the black pen dries and may have start-up problems.
Paper — Coated paper — Architectural D size 24 x inches — sheets. This is very important. Paper — Opaque bond paper — D size 22 x inches — sheets. Lower the lever, making sure that the cable is positioned correctly. Remove the motor, being careful not to force any gear engagements. If the test fails, seevice one of the following: Cartridge — Yellow ink cartridge Latin America. Prevent any slackness or motion of the service station while mxnual is being screwed desginjet place.
Perform the drop detect calibration as follows: How does the customer select a print mode? This site can be found at the following address: Lower trailing-cable holder Removal and Replacement C Reinstalling the Trailing Cable Reinstall the trailing cable following the previous steps in the reverse sequence.
Foot — Foot assembly includes casters — Mounts to the bottom of the plotter stand legs two used. If using D-size media, load the short edge as the leading edge in D-size plotters and the long edge as the leading edge in E-size plotters. Pen checking is set to OFF. These are the area fills that will be affected by a cartridge problem nozzle out or misdirected: You cannot change the handshake setting in the plotters front panel.
TOP Related Posts.
HP DESIGNJET 755CM Manuals & User Guides
Warranty types Warranty removed from product: This product was designated to be returned to HP. Thus, the warranty has been removed from this product. Product sold by third party: This product was sold by a third party. Any warranty support needed would be completed by the third party that sold the product. Product has been exchanged: This product has been exchanged for a new or refurbished product. Please use the product number and serial numbers of the new product to validate warranty status.
Welkom bij de HP Klantenondersteuning. Waarmee kunnen we u van dienst zijn?
HP DesignJet 700, 750C, 750C Plus, and 755CMs -, C4705-90000 Service Manual
HP DESIGNJET 755CM SERVICE MANUAL PDF